DIAG IM3 - Page 120

15Internal 3 Dental Equipment Fixation & Instrumentation Hex Drive Shaft www.vetinst.com Screw Holding Forceps The battery drills we use as a base for our shrouded orthopaedic drills have adjustable torque settings. While it is advised that the final tightenening of the screw is performed by hand, much time and effort can saved by power driving. Risks are low, particularly in the proximal tibia. To power drive using our drill we have created two hex driver extensions to fit into a standard Jacobs chuck. Use 2.5 hex for 2.7, 3.5 and 4.0mm screws and the 3.5 hex for 4.5 and 5.5 screws. A useful instrument for selecting screws with minimal handling. Can be used with any style of screw. SCREW HOLDING FORCEPS SF2055 SF1024 £25.24 £25.24 Screw Holding Forceps 2.4/2.7/3.5/4.5 Screws Screw Holding Forceps 1.0/1.5/2.0/2.4 Screws HEX DRIVE SHAFTS FOR POWER DRIVERS DS25HEX DS35HEX 2.5 Hex Drive Shaft for 2.7, 3.5 & 4.0 Screws 3.5 Hex Drive Shaft for 4.5 & 5.5 Screws Plate Holding Clip £50.99 £50.99 Depth Gauge A useful little clip for holding plates in sequence. Labelled with size. PLATE HOLDING CLIP BPC2 BPC27 BPC35 Accurate measurement of hole depth is essential in order to select the appropriate screw size. A range of Gauges are available for various screw sizes. Hole depth is read from the instrument. Add extra to the measured length to ensure maximal screw thread/bone interface engagement. See chart for additional amount required. Chart supplied with depth gauge or available on request. Use in Self-tapping or Cortical Systems. Plate Holding Clip 2.0mm Plate Holding Clip 2.7mm Plate Holding Clip 3.5mm £10.25 £10.25 £10.25 Whiting Bone Plate Retractor DEPTH GAUGE DG1520 DG2027 DG242735 DG2735 DG4565 For 1.5mm & 2.0mm Screws 115mm For 2.0mm & 2.7mm Screws 135mm For 2.4mm, 2.7mm & 3.5mm Screws 180mm For 2.7mm & 3.5mm Screws 175mm For 4.5mm & 6.5mm Screws 290mm £115.00 £115.00 £115.00 £115.00 £235.00 Load Neutral Drill Guides To exert compression at the fracture site, the cortical screw must be positioned precisely within the slot in the compression plate.The Load/ Neutral Drill Guide has two tips, one for compression (load) and one where no compression is exerted (neutral).There is one combination for each screw/ plate size. Each guide is marked with the drill size to be used. Developed by Colin Whiting the Bone Plate Retractor is designed to expose the end hole(s) of the plate for screw placement. It is often the case that a plate is pushed under soft tissues to avoid unnecessarily large exposures only to find that it is very difficult to access the last screw hole. The bone plate lever slides along the plate until the tip drops over the end. The handle is then elevated and the tip of the lever hooks onto the end of the plate. As the retractor is lifed the end hole of the plate is exposed allowing free insertion of drills taps and screws. LOAD NEUTRAL DRILL GUIDES LNDG15 LNDG20 LNDG24 LNDG27 LNDG35 LNDG45 LNDG55 For 1.5mm Compression Plates For 2.0mm Compression Plates For 2.4mm Compression Plates For 2.7mm Compression Plates For 3.5mm Compression Plates For 4.5mm Compression Plates For 5.5mm Compression Plates £159.65 £159.65 £159.65 £159.65 £159.65 £159.65 £159.65 WHITING­BONE PLATE RETRACTOR BPR3535 BPR2427 BPRSET 104 Whiting Bone Plate Retractor 3.5/3.5 Broad Whiting Bone Plate Retractor 2.4/2.7 Whiting Bone Plate Retractor Set £77.25 £72.10 £139.05